Screw Mount Breakout Card Type-1
Accepting 26-18 AWG wires
all Raspberry Pi
- Routes all 40 I/O and power pins to screw terminal blocks
- Permits easy and secure field installation
- Prototype area for your custom projects
- 2.54mm Pitch PCB screw Terminal Block Connectors
- Rated voltage: 300V
- Rated current: 10A
- Wire range: 24 – 18 AWG
Screw Mount Breakout Card for Raspberry Pi
This card can be used both for Raspberry Pi and for the HOME Automation Card. The 2×20 pin header can be plugged into Raspberry Pi or into any stackable expansion card. It brings all 40 pins to screw-mount terminal blocks for conveniently wiring your project. Measuring only 104mm x 52mm, the card adds a prototype area with 5 x 40 PCB holes spaced at 0.1″ apart where you can install your through hole parts for your own custom project. The terminal blocks accept 26 to 18 AWG wires and are rated 6A/150V.
Screw Mount Breakout Card Layout
The layout below shows the correspondence between the GPIO pins and the Raspberry Pi Breakout card.
USING THE BREAKOUT CARD with the HOME Automation Card
The HOME Automation Card has all the IO signals brought out to a 2×20 right angle male header similar in layout with the Raspberry Pi GPIO header. Since the Breakout Card has a 40 pin female header, it can be used for the HOME Automation Card as well. Please note that when the card is installed on the Raspberry Pi, pin 1 is opposite from the installation on the Home Automation card.
PRACTICAL APPLICATION: Measure 10V signals using the HOME Automation Card
A 0-10V analog voltage output is one of the most common output signals used on process and HVAC instrumentation; due to the number of industrial controllers that will accept or input this signal. The Home Automation Card has 8 analog inputs which can read signals of 0-3.3V. If you want to read 0-10V signals, you need to add an external resistor divider. The Breakout Card Type 1 offers a very convenient way to implement this feature.
Assume you want to modify signal ADC0, which connects to Pin-19 of the expansion connector of the HOME Automation Card (see Schematic). As you can see in the layout, this pin connects to Pin-10 of connector J2.
1. Cut the trace from J2 Pin-10 to the 40 pin connector:
2.Install the resistor dividers.
For this example we selected 1K and 2K resistors. You need to connect the two resistors in series, the connect open end of the 2K resistor to the input signal, and the open end of the 2K resistor to ground. The divided signal between the two resistors will be 1/3rd of the input signal and will be routed to the GPIO connector.
No more cuts or jumpers are required. You can solder the two resistors as shown in the picture below:
Now your Home Automation card can read 10V signals on ADC0. You can repeat the process for all analog inputs. You can also scale the input voltage to higher values using a different resistor divider.
We have three breakout cards for Raspberry Pi, to satisfy all your prototyping needs. All cards plug into the Raspberry Pi 40 pin GPIO connector and bring the IO’s to different terminal blocks.
- Screw Mount Breakout Card Type-1. The card has a large prototype area of 5 x 40 holes at 0.1″ spacing which can be used to test your own hardware. The terminal blocks accept 26 to 18 AWG wires and are rated 6A/150V.
- Spring Loaded Breakout Card Type-2. This card uses spring loaded terminal blocks, which permit rapid connection to I/O pins without any tools. The card has a prototype area of 7 x 19 holes at 0.1″ spacing which can be used to test your own hardware. The terminal blocks accept 22-18 AWG wires and are rated 5A-300V.
- Pluggable Breakout Card Type-3. This card connects the GPIO pins to heavy-duty pluggable terminal blocks. It can use used both for Raspberry Pi and for the HOME Automation Cards. The 2×20 pin header can be plugged into Raspberry Pi or into any stackable expansion card or HAT. The terminal blocks accept 24 to 14 AWG wires and are rated 8A/300V.
|Dimensions||5 × 10 × 1 cm|
- 2D Drawing – coming soon
Raspberry Pi RELAYS$30.00
8-Layer Stackable Card
for Raspberry PiAdd to cart
- Eight RELAYS with Status LEDs
- Eight layer stackable to 64 relays
- Heavy Duty Pluggable Terminal Blocks
- 4 Relays with NO and NC Contacts, rated 4A/120VAC or 4A/24VDC
- 4 Relays with NO only Contacts rated 8A/48VAC or 8A/24VDC
- Software self-test
- Command Line and Python Drivers
Uno, Nano, Teensy, Feather, ESP32$10.00
Raspberry Pi Replacement
for all I2C I/O CardsAdd to cart
- Mechanical dimensions identical with Raspberry Pi HAT
- Replace Raspberry Pi with Arduino UNO or NANO, TEENSY, FEATHER or ESP32
- All required hardware included for any one of the five families
- Connector soldering required
8-Layer Stackable Card
for Raspberry PiAdd to cart
- 32-bit Processor running at 48MHz
- Eight relays with status LEDs and pluggable connectors
- Eight layer stackable
- Eight 12-bit A/D inputs
- Four 12-bit DAC outputs (0-10V dimmers) or
- Four open-drain outputs (30V/5.7A MOSFETs)
- Eight optically isolated digital inputs
- 30 GPIOs (26 GPIOs from Raspberry Pi + 4 new)
- On-board hardware watchdog
- On-board resettable fuse
- Command line and Python drivers
- Node-Red source code examples
- All mounting hardware included: stand-offs, screws and nuts
- Hardware self-test with included loop-back card
- Open source hardware and schematics